Blog Post

Beginnings of a Grave Monument

Early headstones were made out of slate
which was available locally in early New England. The next material to become popular was marble, but after time the marble would erode and the names and particulars of the deceased were indecipherable. By 1850, granite become the preferred headstone material due to its resilience and accessibility. In modern memorials granite is the main raw material used.

Granite is an igneous rock composed primarily of quartz, feldspar, and plagioclase feldspar with other small bits of minerals mixed in. Granite can be white, pink, light gray, or dark gray. This rock is made from magma (molten material) that is slowly cooled. The cooled magma is unearthed through shifts in the earth's crust and erosion of soil.

The first step is to choose the type (typically marble or granite) and color of the stone. The granite block is then cut from the bedrock. There are three ways of doing this. The first method is drilling. This method uses a pneumatic drill that bores vertical holes 1 in (2.54 cm) apart and 20 ft (6.1 m) deep into the granite. The quarrymen then use 4 in (10.1 cm) long steel bits that have steel teeth to cut away at the core of the rock. Jet piercing is much faster than drilling, about seven times so. In this method, 16 ft (4.9 m) can be quarried in one hour. The process uses a rocket motor with a hollow steel shaft to expel a blend of pressurized hydrocarbon fuel and air in the form of a 2,800°F (1,537.8°C) flame. This flame is five times the speed of sound and cuts 4 in (10.2 cm) into the granite.

Process 1

The third way is the most efficient method, quieter, and produces almost no waste. Water jet piercing employs water pressure to cut the granite. There are two systems of water jet piercing, low pressure and high pressure. Both emit two streams of water, but the low pressure system streams are under 1,400-1,800 psi, and the high pressure streams are under 40,000 psi. The water from the jets is reused, and the method minimizes the mistakes and wasted material.

The next step is to remove the block from the quarry bed. Workers take large pneumatic drills tipped with 1.5-1.88 in (3.81-4.78 cm) steel bits tipped with carbide and drill horizontally into the block of granite. They then place paper-wrapped blasting charges into the holes. Once the charges are set, the block makes a clean break from the rest of the rock. Granite blocks are usually about 3 ft (0.9 m) wide, 3 ft (0.9 m) high, and 10 ft (3 m) long, weighing about 20,250 lb (9,185 kg). Workers either loop a cable around the block or drill hooks into either end and attach the cable to the hooks. In both ways the cable is attached to a large derrick that lifts the granite block up and onto a flatbed truck that transports it to the headstone manufacturer. The quarries tend to be independently owned and sell the granite to manufacturers, but there are some larger companies that own quarries. After arriving at the manufacturing house, the granite slabs are unloaded onto a conveyor belt where they are cut into smaller slabs. The slabs are generally 6, 8, 10, or 12 in (15.2, 20.3, 25, and 30.4 cm, respectively) thick. This step is done with a rotary diamond saw. The saw is equipped with a 5 ft (1.5 m) or 11.6 ft (3.54 m) solid steel diamond blade. The blade usually has about 140-160 industrial diamond segments and has the ability to cut an average of 23-25 ft 2 (2.1-2.3 m 2 ) an hour. The cut slabs are passed under a varying number of rotating heads (usually eight to 13) with differing levels of grit arranged

Process 2

The manufacturing of a headstone, from the most abrasive to the least. The first few heads have a harsh diamond grit, the middle heads are for honing, and the last few heads are equipped with felt buffer pads. These pads have water and aluminum or tin oxide powder on them to polish the stone to a smooth, glossy finish. The polished slab is then moved along the conveyor belt to the hydraulic breaker. The breaker is equipped with carbide teeth that exert close to 5,000 psi of hydraulic pressure on the granite slab, making a vertical cut through the stone. The cut stone is then fashioned into the appropriate shape. This is either done by hand with a chisel and hammer, or more precisely with a multi-blade diamond saw. This machine can be set to hold up to 30 blades, but usually is only loaded with eight or nine. Equipped with nine blades, this multi-bladed diamond saw can cut 27 ft 2 (2.5 m 2 ) an hour. The surfaces of the stone are then polished again. In a highly automated process, 64 pieces can be polished at a time. The vertical edges are polished by an automated polishing machine, similar to the surface polisher. This machine chooses the harshest grit head and works it across the vertical edges of the stone. The machine then works its way through the other grits until the edges are smooth. The radial edges are ground and polished at the same time using two diamond grinding drums. One has a harsh grit diamond, and the second has a finer grit. The stone's radial edges are then polished. If intricate stone shapes are needed, the polished stone is moved to the diamond wire saw. The operator adjusts the saw and starts the process, which uses computer software to etch the shapes into the headstone. Any fine etching or detailing is finished by hand. The headstone is then ready for finishing. Rock Pitching entails chiseling the outer edges of the stone by hand, giving a more defined, personal shape.

Process 3

Now that the headstone is polished and shaped, it is time for the engraving. Sandblasting is generally used. A liquid glue is applied to the headstone. A rubber stencil is applied over the glue and then covered with a carbon-backed layout of the design. The carbon transfers the design prepared by the draftsman, onto the rubber stencil. The worker then cuts out the letters and design features that are wanted on the stone, exposing them to the sandblasting. The sandblasting is either manually done or automated. Either method is done in an enclosed area due to the dangers of the process. The worker is entirely covered to be protected from the grains reflected off the stone. The course cutting abrasive is exerted at a force of 100 psi. Dust collectors collect and save the dust for reuse. The stone is then sprayed with high pressure steam to get rid of any leftover stencil or glue. It is again polished and closely inspected, then packaged in cellophane or heavy paper to protect the finish. The package is placed in crates and shipped to the customer or funeral director.

There are many new techniques that use innovative software to etch designs on headstones. Laser etching is an upcoming development that allows pictures and more intricate designs to be put on the headstone using a laser beam. The heat from the laser pops the crystals on the surface of the granite, resulting in a elevated, light-colored etching.

Read more: http://www.madehow.com/Volume-7/Headstone.html#ixzz3bacdYqYY

Cold Spring Granite Brochure. 17 October 2001. < http://www.coldspringgranite.com >. Elberton Granite Association, Inc.

Monumnet Builders of North America. The Monument Industry Certification Manual. July 1993. < http://www.monumentbuilders.org >.

Rock of Ages Web Page. 17 October 2001. < http://www.rockofages.com >. Deirdre S. Blanchfield

Read more: http://www.madehow.com/Volume-7/Headstone.html#ixzz3baloW9Cs


About Us

We engrave inscriptions, logo art work and addresses into natural stone, wood, plated metals and etch glass using custom design. We design, manufacture and supply a full line of granite monuments, memorials, tombstones, urns, vases, benches, statues, specialized mobile sandblasting, and stone carving, including graphic design service. Domestic Limited Liability Company / State Registry # 924856-98